niya support


Niya Tracker 75

FAQ

The Tracker is designed for powerful, efficient cleaning, featuring four motors—dual driving motors and dual suction motors—that ensure optimal performance. Using Smart Sonar Navigation, the Tracker detects walls. Cleaning mode customization through the app allows you to choose from five different modes, tailoring the cleaning process to your pool’s specific needs. The waterline mode includes a horizontal cleaning feature, providing an even more precise cleaning along the waterline. For improved filtration, the Tracker is equipped with a Hyperfine filter, capturing even the smallest debris to leave your pool cleaner than ever.

The Tracker 75 is suitable for above-ground and in-ground pools, up to 15 m. The water should be at least 0.4 -2.5 m above the device.

The warranty on the Tracker 75 is 24 months.

Charge your Tracker 75 in a shaded, dry area. Do not use an extension cord to connect the battery charger to the electrical socket. For user safety, place the battery charger at least 11 cm above the ground while in use.
 
1. Connect the robot to the electrical socket using the provided battery charger. The LED on the robot will flash GREEN during the charging process.
2. When the device is fully charged, the LED on the robot will show steady GREEN. After 10 minutes, it will turn off automatically.
3. Disconnect the charger from the robot and the electrical socket.

The Tracker 75 has a charge time of 4 hours.
 
Once fully charged, it offers up to 3 hours of cleaning in 5 different cleaning modes: Standard Mode, Floor-Only, Walls Mode, Waterline Mode, and Eco Mode.
 
the Eco Mode cleans the floor every other day for a full week (3 cleanings in total), providing a more hands-off, low-hassle solution to keep your pool spotless.
 
Choose from these five modes to tailor your cleaning experience to your pool’s needs.

Follow these steps to replace the battery:
 
Make sure the robot is powered OFF.
 
1. Turn the robot upside down.
2. Unscrew the six screws surrounding the battery at the bottom of the robot.
3. Remove the battery and clean the battery area with a towel from any water residue.
4. Insert the new battery into the battery slot.
5. Tighten the screws in surrounding the battery.

Keep your Tracker 75 in top shape with these simple cleaning steps!
 
1. Position the pool cleaner on a solid surface at the poolside, ensuring it is switched off.
 
2. Lift the robot lid to access the filter compartment.
 
3. Take out the filter basket.
 
4. Remove the filter lid.
 
5. Rinse or wash both the filter basket and the robot body thoroughly with a garden hose to remove any debris and dirt.
 
 

The Tracker 75 offers five cleaning modes: Standard Mode, Floor Mode, Walls Mode, Waterline Mode, and Eco Mode.
 
The pool cleaner is set by default on Standard Mode and will revert back to Standard Mode once it shuts off.
 
Standard Mode: This mode provides up to 3 hours of floor, wall, and waterline cleaning. The robot cleans the floor, wall, and waterline for the first hour and the floor only for the second hour.
 
Floor Mode: This mode provides up to 3 hours of Floor-Only cleaning.
 
Walls Mode: This mode provides up to 3 hours of Wall cleaning.
 
Waterline Mode: This mode provides up to 3 hours of Waterline cleaning.
 
Eco Mode: With Eco Mode, the Tracker 75 completes three shorter floor-only cleaning cycles for 1 week, on a single battery charge.
 
To set the Cleaning Mode:
 
1. Press the Power button to turn the robot ON.
2. Short press the Power button until you reach the desired cleaning mode.
 

Carefully follow the instructions below to clean the impeller.
 
1. Turn OFF the robot: Press and hold the button until the LED turns off.
 
2. Clean the sensors: Wipe the metallic out-of-water sensors on the robot's top with a tissue to ensure they are completely dry.
 
3. Remove the impeller cover: Remove the 2 screws to take off the impeller cover.
 
4. Carefully remove debris from the impeller area (with a tweezer or a similar tool). Gently return the cover and screws.

Solid Display:

Blue - Device working
Red - Device Error
Green - While Working: ECO mode, While connected to the charger: Fully charged
Purple - Device Stuck During Operation

Flashing Display:

Blue - Flash every 1 sec: Device Starting. Flash every 3 sec: Device Idle. Flash every 30: Device idlein ECO mode
Green - Device charging
Yellow - Low Battery
Purple - Cleaning mode has changed
White - Software Update

If your Tracker 75 isn't climbing, try the following troubleshooting steps:
 
1. Check that your Tracker is not set to Floor-only mode.
Note that in Standard Mode, the robot cleans the floor, walls, and waterline for the first hour, then focuses on the floor only during the second hour of cleaning.
 
2. Ensure the pool temperature is above 15°C. Cold water can affect the robot's ability to climb effectively.
 
3. Ensure the chemical levels in your pool are within the recommended parameters.

You can download the Niya App to your mobile device from either the Google Play store for Android or the App store for iOS.
The app is compatible with the following smart devices:
Apple (iOS) – Version 10 and up – iPhone, iPad
Android – Version 5 and up operating system
 

The foam filter included with your Tracker 75 is an add-on to your filter that helps capture ultra-fine debris. The foam filter can be used when the robot is operating in Floor-Only Mode. However, the foam can make it more difficult for the robot to climb walls, so it should be removed before switching to a wall cleaning mode. For optimal performance, it is recommended to replace the foam after every five uses. As the foam absorbs fine debris, it will gradually turn brown with each cleaning cycle.

Niya Tracker Manual de Usuario

Manual de Usuario

Todo sobre tu Tracker 75
Descargar
Niya tacker 75 Recambios

Recambios Originales

Tracker 75
Comprar
¿Necesitas más ayuda?
Escríbenos